Absolute single turn hollow shaft encoders with 10 bit parallel gray output in a robust housing for harsh environments. Some options are not available on all units, see the 567 and, 569 datasheet for the full specification and ordering details. Counting direction reversal via input signal.

• Brief specification -
• 58mm diameter mounting flange
• 10 bit parallel Gray code short circuit protected TTL or HTL outputs
• Protection to IP65
• Enable function
• 5Vdc or 9-30 Vdc polarity protected supply
• Direction and enable inputs (not with 12pin EML connector)
• 8mm, 10mm, 12mm, 14mm diameter hollow shaft options
• Termination options - 1.5M cable (16x0.25mm), other lengths to order, 12pin EML Connector

Absolute single turn shaft encoders with 10 bit parallel Binary or Gray code (possible with excess-code) output in a robust housing for harsh environments. Some options are not available on all units, see the 670 and 671 datasheet for the full specification and ordering details. Counting direction reversal via input signal.

• Brief specification -
• General specification as the 567 and 569 (above)
• Mounting flange - 36mm diameter clamp or 58mm Synchro
• 10 bit parallel Gray code in Sink, Source, TTL or HTL outputs
• Hold and Direction inputs
• 6mm or 10mm shaft options with flats
• Termination options - 1.5M cable (16x0.25mm), other lengths to order, 12pin EML, 19pin PT

Absolute single turn shaft encoders with 10 bit serial binary or gray code output in a robust housing for harsh environments. Some options are not available on all units, see the 670 and 671 datasheet for the full specification and ordering details. Counting direction reversal via input signal.

• Brief specification -
• Mounting flange - 36mm diameter clamp or 58mm Synchro
• 10 bit SSI Binary or Gray code
• CAN Open and BiLL Interfaces
• Hold and Direction inputs
• 6mm or 10mm shaft options with flats
• 5Vdc or 9-30 Vdc polarity protected supply
• Termination options - 1.5M cable (12x0.25mm), other lengths to order, 12pin EML, 19pin PT
• Cable length 100M or to RS485 specification

Absolute single turn 10 bit shaft encoders with analog output in a robust housing for harsh environments. Output signal direction reversal via input signal, non volatile memory for retention of settings. Some options are not available on all units, see the 670 and 671 Analog datasheet for the full specification and ordering details.

• Brief specification -
• Mounting flange - 36mm diameter clamp or 58mm Synchro
• 0-20mA or 4-20mA outputs
• ZeroSet function and Direction inputs
• Free choice of active angle of 10° up to 360°
• 6mm or 10mm shaft options with flats
• 9-36 Vdc polarity protected supply
• 1.5M cable 6x0.25 2x0.35 shielded, other lengths to order

Absolute single turn shaft encoders with 12 bit parallel Binary or Gray code (possible with excess-code) output in a robust housing for harsh environments. Some options are not available on all units, see the 672 Parallel datasheet for the full specification and ordering details. Counting direction reversal via input signal.

• Brief specification -
• Mounting flange - 36mm diameter clamp or 58mm Synchro
• 12 bit parallel Gray code TTL or HTL outputs, short circuit protected
• Direction input
• 6mm or 10mm shaft options with flats
• 5V or 11-30 Vdc polarity protected supply
• Termination options - 1.5M cable (16x0.25mm), other lengths to order, 19pin PT

Absolute single turn shaft encoders with 12 bit SSI serial binary or gray code output in a robust housing for harsh environments. Some options are not available on all units, see the 672 Serial datasheet for the full specification and ordering details. Counting direction reversal via input signal.

• Brief specification -
• Mounting flange - 58mm Synchro
• 12 bit SSI Binary or Gray code
• CAN Open and BiLL Interfaces
• Hold and Direction inputs
• 6mm or 10mm shaft options with flats
• 5Vdc or 11-30 Vdc polarity protected supply
• Termination options - 1.5M cable (12x0.25mm), other lengths to order, 12pin EML, 8pin PT
• Cable length 100M or to RS485 specification

58mm diameter absolute 13bit single turn and 25bit multi turn encoders. Available with stub or hollow shafts, synchro flanges or stator couplings. Some options are not available on all units, see the 674, 675, 684, 685 SSI datasheet for the full specification and ordering details.

• Brief specification -
• Mounting flange - 58mm Synchro, 36mm clamp or stator coupling
• 13 or 25 bit SSI Binary or Gray code, RS422 output
• 6mm / 10mm shafts or 12mm hollow shaft options
• 10-30 Vdc polarity protected supply
• Connection by radially mounted 17pin EML connector
• Protection - IP66 at housing, IP64 at shaft inlet
• Cable length 100M maximum

58mm diameter absolute 13bit single turn and 25bit multi turn encoders with EnDat, an advanced high speed serial point to point interface. Allows positional reading and setup of the encoder. Some options are not available on all units, see the 674, 675, 684, 685 EnDat datasheet for the full specification and ordering details.

• Brief specification -
• Main specification as the 674, 675, 684, 685 SSI encoders above
• 5Vdc polarity protected supply
• Alarm sensing for fault conditions
• EnDat communicates with Leine & Linde Fieldbus Gateways

58mm diameter absolute 13bit single turn and 25bit multi turn encoders with EnDat, an advanced high speed serial point to point interface. Allows positional reading and setup of the encoder. Some options are not available on all units, see the 674, 675, 684, 685 Profibus datasheet for the full specification and ordering details.

• Brief specification -
• Main specification as the 674, 675, 684, 685 SSI encoders above
• "Plug and Play operation"
• RS485 communcation in Profibus DP profile
• Non manufacturer specific open FieldBus Standard
• Cable length 400M maximum @ 1.5Mb/s